Produktbeskrivning
Adapter för att generera en digital stereosignal i SPDIF-format från MOST25-dataströmmen Lätt att integrera en DSP-produkt i moderna fordon med premium ljudsystem Passar för fordon från Audi, BMW, Mercedes, Porsche och flera andra. Frekvenssvar: 10 - 22.000 Hz
MOST Interface to Mercedes- Benz, BMW, AUDI, Porsche, VW Land Rover and Volvo
Compatibility:
AUDI A4, A5, A6, A8, Q5, Q7 (MMI 2G, 3G) with separate external amplifier
AUDI A4, A5, A6, A8, Q5, Q7 (MMI 3G+)
Compatibility:
BMW E60, E61, E63, E64, E70, E71, E72, E90-E93.
BMW F01, F02, F03, F07, F10, F11, F12, F13, F16, F20, F25, F30, F31, F34. BMW G-series
BMW E65, E66
Compatibility:
Land Rover Freelander 2
Land Rover Freelander 2 (HSE)
Land Rover Discovery-3, Discovery-4 until 2013, Range Rover Sport until 2012.
Range Rover Evoque, Range Rover Sport 2012+,
Compatibility:
Mercedes Benz until 2009 (NTG1 audio systems without external unit the AGW and NTG2).
Mercedes Benz (NTG1 audio system with the external unit AGW) - W211, W219, W220.
Mercedes Benz (NTG3 and NTG3.5 audio systems, audio systems with AGW block the production of Becker).
Mercedes Benz 2008+ (NTG2.5, NTG4, NTG4.5 audio systems).
Compatibility:
Porsche until 2009 (Cayenne, etc. with PCM2.0 and PCM2.1).
Porsche 2009+ (Cayenne, etc. with head unit PCM3.0)
Compatibility:
Volvo S80, XC70 until 2012,
Volvo XC70 2012+ and some models Volvo S60, V60
Volvo S60, V60
Volvo XC60 Premium
Volvo XC90, S40, V50. The standard phone module is not supported.
Dimensions adapter: 90 х 60 х 25 mm
Power supply voltage: 8 ... 16 volts
Current consumption in sleep mode: less than 0.5 mA
Digital output: SPDIF / TosLink
Sound Processor: 24 bit
Dynamic range: no less than 100 db
Package incl.
Power cable
Jumpers – 3pcs
Quick guide
Depending on vehicle specification, possibly additionally required (sold separately):
Optical cable (0,8m) with connector
for system MMI 3G+ (Audi or VW Touareg NF).
for BMW or MB (if original amplifier is missing).
for Volvo (during the procedure «serial number assignment»),
Only optical connector
for BMW or MB (if the original amplifier is present).
Notes for BMW and Mercedes Benz (If the optical amplifier Logic-7 is not in the original
vehicle specification):
It is necessary to register in the configuration of the vehicle using the diagnostic
equipment,
To connect the adapter, you will also need an optical cable with connector (not
supplied).
Notes for BMW: an additional mode of the adapter (BMW spec.mode (park)). This mode
should be used if you want to change the volume of the signal (parking sensors and system
messages). Read more about this mode in the Applications.
Notes for Mercedes Benz (only for Comand NTG2.5):
- It is necessary to activate function “Rearseat entertainment”.
Notes for Volvo and Land Rover (if you have activated component protection):
Before connecting the adapter must be assigned to the adapter serial number (a marker of
activity of the protection components is the cessation of broadcast audio adapter in 20-40
seconds after turning on the system).
For the assignment you need to set the jumpers to position «Read Serial Number», then,
not disconnect the original amplifier, connect the adapter to the optical interface MOST and
turn on audiosystem. After you enable the adapter «read» the serial number of original
amplifier and store it in its non-volatile memory. This procedure usually takes less than 20
seconds, a sign of the end of the procedure «Read Serial Number» is the formation of pulses
with an interval of 1 second on the line Remout (blue wire). After that you should disable
original amplifier, set the jumpers to a position corresponding to the car and use the audio
interface in the system instead of the original amplifier.
